2” x 26” | 300 GPD | 150 PSI | Low Energy RO Membrane | Applied Membranes

In Stock for Immediate Shipment.
More Information

2" x 26"  Low Energy Reverse Osmosis Membrane | Tap Water | 450 GPD at 150 PSI | LE RO Membrane

AMI Low Energy (Low Pressure) RO Membrane elements are specially designed to run at 150 psi while producing the same product flow as standard elements. By using these elements in your commercial reverse osmosis system, you can significantly reduce your operating costs in tap water applications.

AMI Low Energy RO membrane elements produce high quality water from tap or brackish water in small commercial RO systems, and are among the finest in the industry.  With hundreds of thousands of membranes in operation in water filtration systems world-wide, AMI membranes have earned a reputation of delivering consistent, reliable, and long lasting  performance, making AMI Membranes the natural choice for use in small commercial RO systems.  AMI LowEnergy Commercial RO Membranes are constructed of low pressure tap water TFC (thin film composite) membrane material and fit standard PVC and Stainless Steel RO Membrane Housings. 

AMI Membranes are Made in the USA in their ISO 9001:2015 Certified Facility and are 100% Quality and Performance Tested.

Genuine AMI Membranes ISO USA Quality


M-T2026ALE Specifications

AMI Part Number: M-T2026ALE
Membrane Size (Nominal): 2 x 26
Membrane Dimensions: 1.8"Dia. x 26"L
Flow Rate: 300 GPD (1,135 LPD)
Applied Pressure: 150 psi (1 MPa)
Stabilized Salt Rejection: 99%
For Housing: Standard 2" x 26"
Outer Wrap: Tape Wrapped
Membrane Type: Tap or Brackish Water
Membrane Sheet: TFC (Thin Film Composite)
Element Type: Spiral Wound
Feed Water Test Temperature: 77°F  (25°C)
Single Element Recovery: 10%
Chlorine Tolerance: 0
Feed water pH Range: 2-11
For Housing: 2" x 26"
Manufacturer: Applied Membranes, Inc.
Country of Manufacture: United States (USA)

AMI Membranes Product Specifications

Note: Performance specifications based on 2,000 mg/l sodium chloride, 150 psi (1 MPa) applied pressure, 77ºF (25ºC) feed water temperature, pH 8 and the recovery listed in the table above. Element permeate flow may vary ± 20%. Caution: Do not run these membranes at a pressure that will produce more than their rated product flow rate. This will lead to premature fouling of the membrane resulting in drop in permeate flow and higher TDS of the permeate.

Features of AMI LE Low Pressure Tap Water / Brackish Water RO Membranes

  • Reduce operating costs and wear and tear on your system by running your system at a lower pressure.
  • High Rejection & Flow Rate
  • Made in the USA
  • Manufactured in our ISO 9001:2015 Certified Facilities
  • 100% Performance and Quality Tested
  • Backed by our Experienced Technical Support Staff
  • High Quality for Consistent and Reliable Performance
  • Uses the most advanced membrane film technology and manufacturing processes
  • Standard dimensions to fit in commonly available housings

Applications for AMI Low Pressure RO Membranes

  • Restaurants
  • Aquariums
  • Whole House (Residential)
  • Office
  • Institutions
  • Hotels
  • Hospitals
  • Disaster Relief
  • Spot Free Rinse/Car Wash
  • Labs
  • Pharmaceutical
  • Humidification
  • Misting
  • Manufacturing
  • Rinse Water
  • Bottled Water
  • Water stores
  • Beverage
  • Food Processing
  • Ice Makers
  • Commercial Water Treatment
  • Ice Makers
  • Tap Water
  • Brackish Water
  • Wide Variety of Other Applications

M-T2026A 2

Physical Dimensions of M-T2026ALE:


Total Length (L):

26 In. (66 cm)

Membrane Length (I):

23.64 In. (60 cm)

Diameter (D):

1.8 In. (4.6 cm)

PWT (P):

0.68 In. (1.7 cm)